Spicer Driveshafts for Improved Strength in Your Jeep® JT
PROBLEM
Following certain modifications to a Jeep Gladiator JT, the factory driveshaft may not stand up to increased torque and angle demands, and it may contribute to excessive vibration.
SOLUTION
Optimized for lifted vehicles and engineered to deliver increased strength and reduced critical speed issues, Spicer® performance driveshafts are renowned for their ruggedness and high quality: the Spicer heavy-duty 1350 driveshaft for Gladiator garnered a 2020 Global Media Award at SEMA 2019.
Dana provides off-roaders with an upgrade for their Jeep Gladiator JT, with these high-performance 1310 and 1350 Series Spicer® driveshafts. Find out why the Spicer name has been trusted for generations, and why our innovations will continue to inspire Jeep owners to push the boundaries for years to come.
- Engineered with a smaller diameter for improved clearance to the exhaust
- Include a direct-fit bolt-in flange
- Provide ease of installation and a better off-road experience
- Deliver strength that can exceed even original equipment
- Tubes are thicker for added strength
Note: To ensure the proper fitment, it is best to measure your application after any axle and lift installation.
These Spicer driveshafts are optimized for 0" - 6" lifts
Two-Piece 1350 Series Rear Driveshaft with CV Joints for the Jeep Gladiator JT
The new two-piece Spicer® 1350 series driveshaft for the Jeep Gladiator JT is engineered as a direct bolt-in solution for increased strength. Featuring several upgrades designed for added durability on the trail, this driveshaft includes 3" DOM tubing. Dana gives you everything you need for the upgrade, including a center bearing drop bracket kit designed to accommodate lifted vehicles.
- 100% bolt-in direct fit
- All hardware included, no adapter flange or new yokes needed
- High angle flange yoke at the axle
- Service free means more driving and less maintenance
- Lubed-for-life SPL® 1350 series u-joint
- Permanently sealed high temperature CV boots
- Dana-designed CV joint with high performance HNBR boot
- Two-piece design
- Ensures no critical speed issues
- Allows for smaller OD, yet high strength 3×0.083 DOM tubing
- Allows for best possible break over angle
Spicer 1350 Heavy Duty Rear Driveshaft for Jeep Gladiator JT with Ultimate Dana 60™ axles
| Application | Position | Part # | Length - Collapsed/Extended (Inches) |
|---|---|---|---|
| Jeep Gladiator JT (UD60JT) | Rear | 10132306 | 60.3 / 66.6 |
Spicer 1350 Performance Rear Driveshaft for Jeep Gladiator JT with Dana 44™ AdvanTEK® axles
| Application | Axle Model | Position | Part # | Length - Collapsed/Extended (Inches) |
|---|---|---|---|---|
| Jeep Gladiator JT | Dana 44™ AdvanTEK® | Rear | 10132305 | 62.5 / 68.7 |
Spicer® 1350 Series Front Driveshaft for the Jeep Gladiator JT
Built from high-quality steel to deliver the ruggedness and durability you’re already getting in the axles in your Jeep JT, 1350 Series driveshafts are engineered for applications that require high horsepower and torque.
- Maintenance free SPL® 1350 Series double cardan
- Lubed-for-life high performance SPL 1350 series u-joint
- Non-greaseable lubed-for-life double cardan centering package
- Improved lube retention and resistance to contaminants
- No loss of operating angle potential
- High strength tubing
- Smaller diameter 2×0.120 DOM front shafts allow for improved clearance
- 3×0.083 DOM rear shafts ensure no critical speed issues
- Slip member
- Front shafts feature strong 1.375" spline with a re-lube zerk in the seal
- Rear shafts feature 1.5" spline with a re-lube zerk in the slip yoke
- Lubed-for-life high performance SPL 1350 series u-joint at end of each slip yoke
Spicer 1350 Heavy Duty Driveshafts for Jeep Gladiator JT with Ultimate Dana 60™ axles
| Application | Position | Part # | Length - Collapsed/Extended (Inches) |
|---|---|---|---|
| Jeep Gladiator JT (UD60JT) | Front | 10097841 | 33.2 / 36.3 |
| Jeep Gladiator JT (UD60JT) | Rear | 10132306 | 60.3 / 66.6 |
Spicer 1350 Performance Driveshaft for Jeep Gladiator JT with Dana 44™ AdvanTEK® axles
| Application | Axle Model | Position | Part # | Length - Collapsed/Extended (Inches) |
|---|---|---|---|---|
| Jeep Gladiator JT | Dana 44™ AdvanTEK® | Front | 10097840 | 35.9 / 39.0 |
| Jeep Gladiator JT | Dana 44™ AdvanTEK® | Rear | 10132305 | 62.5 / 68.7 |
Spicer® 1310 Series Front Driveshaft for Jeep Gladiator JT (Direct Fit Bolt-In Replacement)
This driveshaft features a smaller diameter, which will not interfere with the Jeep JT exhaust. In addition, you will enjoy the following advantages:
- One-piece flange
- Prevents run-out
- Eliminates need for an adapter
- Bolts to the stock Jeep axle
- Optimized for 0" - 6" lift
- Ideal for larger tires
- Offers improved ground clearance
- Thicker tube than original equipment part
- 50% thicker than OE shaft
- Delivers added strength
Spicer 1310 Performance Front Driveshaft for the Jeep Gladiator JT (Direct Fit Bolt-In Replacement)
| Application | Position | Part # | Length - Collapsed/Extended (Inches) |
|---|---|---|---|
| Jeep JT (0" - 6") | Front | 10020345 | 35.9 / 40.5 |
Locate Driveshafts for the Jeep
Get the lift you’re looking for in your Jeep Wrangler or Gladiator: get in touch with the Spicer parts dealer in your area. And be sure to check out the full range of Dana-backed products designed to unleash the performance in your vehicle at DanaAftermarket.com.
Jeep, Spicer, and Dana — legendary brands built stronger together. Read Our Story
